Annovi Reverberi Pump Seal Price : 20 $

Product Code : A&R2

svg+xml,%3Csvg%20xmlns%3D%27http%3A%2F%2Fwww.w3 - Annovi Reverberi Pump Sealsvg+xml,%3Csvg%20xmlns%3D%27http%3A%2F%2Fwww.w3 - Annovi Reverberi Pump Seal


Annovi Reverberi AR Pump Seal
Annovi Reverberi AR Pump Seal set; 3 high pressure felts, 3 high pressure felts support and 3 water felts.

Pump Seals with time-consuming and improper handling wear;
Water in the pump mixes with water, causing the pump to operate with oil that is not oil-free. This damages the crankshaft, ceramic piston rods, connecting rods, pump bearings.
The pump causes water leakage from the front block, ie water leakage.
Pressure causes your pump to fall and you can no longer perform well on your machine.
Why do the felts of your pressure pump become worn and damaged, distorted?
If your pump freezes during winter months, your pump felts will become worn and damaged.
If your pressure pump has less than 15 liters of water per minute, that is if your pump is working with little water. (The water from the pump flows at least like mains water.)
If the incoming water comes from the well water, but the pressure pump does not use the water filter with the competence feature and the large size.
If the pump comes with dirty water and you are not using a filter.
If you have run your washing machine without water, sometimes the machine can be turned on without opening the water. That is 1500 times per minute ceramic piston will pass through the felts as anhydrous, and because the felts work without water, they will burn without friction.
How do I change the pressure and water felts in the washing machine?
STEP 1: Remove the pump head bolts using a suitable wrench.

Remove the head proportionally by clicking with a plastic hammer (cross hitting).

basinc kecesi 2 - Annovi Reverberi Pump Seal

STEP 2: If you do not have a suitable extractor, you can use a screwdriver as a lever.

Certainly do not rub your bed.

* You will have to change the felt bed even if you draw too little.

basinc kecesi 3 - Annovi Reverberi Pump Seal

STEP 3: Replace the O-rings of the pad bearings.

basinc kecesi 4 - Annovi Reverberi Pump Seal

STEP 4: Place the felt, felt supports and pad bearings in the pump respectively

Note: Grease the pad bearings slightly.

basinc kecesi - Annovi Reverberi Pump Seal

STEP 5: Things to be careful when installing the pump front block after changing the seal

basinc kecesi 41 - Annovi Reverberi Pump Seal

Turn the crank until the middle piston reaches the upper dead point. Grease the ceramic part of the pistons and hold the head at the proper angle to the pistons.

STEP 6: Things to be careful when installing the pump front block after changing the seal

basinc kecesi 5 - Annovi Reverberi Pump Seal

* Grease the ceramic part of the pistons and hold the pump head at the proper angle to the pistons.

* Install stud bolts and washers and gently tighten with allen key.

* Do not neglect to put stamps otherwise you will damage the screws of the brass block.

* When tightening the stud bolts, do not squeeze anyway, so the screws are crosswise tight

Please visit our Machine Repair Workshop we have prepared for you in this and all similar technical issues. We teach you to fish. Now that your cleaning machines are broken, we want to end the search for the mechanic and service. Now click on the image below to repair your own cleaning machine yourself.
svg+xml,%3Csvg%20xmlns%3D%27http%3A%2F%2Fwww.w3 - Annovi Reverberi Pump Seal

The machines are of course degraded, after all, everything has a life. It is important to make the defective machine work again in a short time and prevent it from being damaged again due to the same fault. Use a little more conscious.

oto yikama makinesi yedek parca - Annovi Reverberi Pump Seal

Legal warning
The publisher rights in this website are protected. The copying, modification and reproduction of images, graphics, images, audio files, texts and animations contained in this web site are not permitted except for viewing on the screen only.